74LS240 Octal Buffers Line Drivers IC (74240) DIP-20 Package

74HC109 Dual J-K Positive-Edge-Triggered Flip-Flop IC – DIP-16 Package The 74HC109 is a dual positive edge triggered JK flip-flop featuring individual nJ and nK inputs. It has clock (nCP) inputs, set (nSD) and reset (nRD) inputs and complementary nQ and nQ outputs. The set and reset are asynchronous active LOW inputs and operate independently of the clock input. The nJ and nK inputs control the state changes of the flip-flops as described in the mode select function table. The nJ and nK inputs must be stable one set-up time prior to the LOW-to-HIGH clock transition for predictable operation. The JK design allows operation as a D-type flip-flop by connecting the nJ and nK inputs together. Inputs include clamp diodes. It enables the use of current limiting resistors to interface inputs to voltages in excess of VCC. This product is known as 74109 IC, 74109 SMD IC, 74HC109 IC, 74HC109 SMD IC, Components, Dual J-K Positive-Edge-Triggered Flip-Flops IC, Dual J-K Positive-Edge-Triggered Flip-Flops SMD IC, SN74HC109D, CD74HC109M, 74HC109D, CD74HC109E, SN74HC109N, CD74HC109ME4.

Features :-

• Input Levels :

– For 74HC109: CMOS level – For 74HCT109: TTL level

• J and K inputs for easy D-type flip-flop
• Toggle flip-flop or “do nothing” mode
• Specified in compliance with JEDEC standard no. 7A
• ESD protection:

– HBM JESD22-A114F exceeds 2000 V – MM JESD22-A115-A exceeds 200 V

• Multiple package options

This 8-bit flip-flop features 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. It is particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. The eight flip-flops of the SN74F574 are edge-triggered D-type flip-flops. On the positive transition of the clock (CLK) input, the Q outputs will be set to the logic levels that were set up at the data (D) inputs. A buffered output enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components. The output enable (OE) does not affect the internal operations of the flip-flops. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. The SN74F574 is characterized for operation from 0°C to 70°C.

Features :-

• Eight D-Type Flip-Flops in a Single Package
• 3-State Bus-Driving True Outputs
• Full Parallel Access for Loading
• Buffered Control Inputs
• Package Options Include Plastic Small-Outline Packages and Standard Plastic 300-mil DIPs

The 74HC137 decoder utilizes advanced silicon-gate CMOS technology and is well suited to memory address decoding or data routing applications. The circuit features high noise immunity and low power consumption usually associated with CMOS circuitry, yet has speeds comparable to low power Schottky TTL logic. The 74HC137 has 3 binary select inputs (A, B, and C). If the device is enabled, these inputs determine which one of the eight normally HIGH outputs will go LOW. Two active LOW and one active HIGH enables (G1, G2A and G2B) are provided to ease the cascading of decoders. The decoder’s outputs can drive 10 low power Schottky TTL equivalent loads, and are functionally and pin equivalent to the 74LS137. All inputs are protected from damage due to static discharge by diodes to VCC and ground.

Features:-

• Combines 3-to-8 decoder with 3-bit latch
• Multiple input enable for easy expansion or independent controls
• Active LOW mutually exclusive outputs
• Low-power dissipation
• Complies with JEDEC standard no. 7A
• Multiple package options

The 74F240 are octal buffers and line drivers designed to be employed as memory and address drivers, clock drivers and bus-oriented transmitters/receivers which provide improved PC and board density.

Features:-

• 3-STATE outputs drive bus lines or buffer memory address registers
• Outputs sink 64mA (48mA mil)
• 12mA source current
• Input clamp diodes limit high-speed termination effects