74F64 4-2-3-2-Input AND-OR-Invert Gate IC (7464) DIP-14 Package

The 74F109 is a dual positive edge-triggered JK-type flip-flop featuring individual J, K, clock, set, and reset inputs; also true and complementary outputs. Set (SD) and reset (RD) are asynchronous active low inputs and operate independently of the clock (CP) input. The J and K are edge-triggered inputs which control the state changes of the flip-flops as described in the function table. Clock triggering occurs at a voltage level and is not directly related to the transition time of the positive-going pulse. The J and K inputs must be stable just one setup time prior to the low-to-high transition of the clock for predictable operation. The JK design allows operation as a D flip-flop by tying J and K inputs together. Although the clock input is level sensitive, the positive transition of the clock pulse between the 0.8V and 2.0V levels should be equal to or less than the clock to output delay time for reliable operation

Features :-

Industrial temperature range available (–40°C to +85°C)

The 74F541 except that the inputs and outputs are on opposite sides of the package (see Connection Diagrams). This pinout arrangement makes these devices especially useful as output ports for microprocessors, allowing ease of layout and greater PC board density

Features :-

• 3-STATE outputs drive bus lines
• Inputs and outputs opposite side of package, allowing easier interface to microprocessors

74HC109 Dual J-K Positive-Edge-Triggered Flip-Flop IC – DIP-16 Package The 74HC109 is a dual positive edge triggered JK flip-flop featuring individual nJ and nK inputs. It has clock (nCP) inputs, set (nSD) and reset (nRD) inputs and complementary nQ and nQ outputs. The set and reset are asynchronous active LOW inputs and operate independently of the clock input. The nJ and nK inputs control the state changes of the flip-flops as described in the mode select function table. The nJ and nK inputs must be stable one set-up time prior to the LOW-to-HIGH clock transition for predictable operation. The JK design allows operation as a D-type flip-flop by connecting the nJ and nK inputs together. Inputs include clamp diodes. It enables the use of current limiting resistors to interface inputs to voltages in excess of VCC. This product is known as 74109 IC, 74109 SMD IC, 74HC109 IC, 74HC109 SMD IC, Components, Dual J-K Positive-Edge-Triggered Flip-Flops IC, Dual J-K Positive-Edge-Triggered Flip-Flops SMD IC, SN74HC109D, CD74HC109M, 74HC109D, CD74HC109E, SN74HC109N, CD74HC109ME4.

Features :-

• Input Levels :

– For 74HC109: CMOS level – For 74HCT109: TTL level

• J and K inputs for easy D-type flip-flop
• Toggle flip-flop or “do nothing” mode
• Specified in compliance with JEDEC standard no. 7A
• ESD protection:

– HBM JESD22-A114F exceeds 2000 V – MM JESD22-A115-A exceeds 200 V

• Multiple package options

The functional characteristics of the 74F194 4-Bit Bidirectional Shift Register are indicated in the Logic Diagram and Function Table. The register is fully synchronous, with all operations taking place in less than 9ns (typical) for 74F, making the device especially useful for implementing very high speed CPUs, or for memory buffer registers. The 74F194 design has special logic features which increase the range of application. The synchronous operation of the device is determined by two Mode Select inputs, S0 and S1. As shown in the Mode Select-Function Table, data can be entered and shifted from left to right (shift right, Q0→Q1, etc.), or right to left (shift left,Q3→Q2, etc.), or parallel data  can be entered, loading all 4 bits of the register simultaneously. When both S0 and S1 are Low, existing data is retained in a hold (do nothing) mode. The first and last stages provide D-type Serial Data inputs (DSR, DSL) to allow multistage shift right or shift left data transfers without interfering with parallel load operation. Mode Select and data inputs on the74F194 are edge-triggered, responding only to the Low-to-High transition of the Clock (CP). Therefore, the only timing restriction is that the Mode Select and selected data inputs must be stable one setup time prior to the Low-to-High transition of the clock pulse. Signals on the Mode Select, Parallel Data (D0–D3) and Serial Data(DSR, DSL) can change when the clock is in either state, provide donly the recommended setup and hold times, with respect to the clock rising edge, are observed. The four Parallel Data inputs(D0–D3) are D-type inputs. Data appearing on (D0–D3) inputs whenS0 and S1 are High is transferred to the Q0–Q3 outputs respectively, following the next Low-to-High transition of the clock. When Low, the asynchronous Master Reset (MR) overrides all other input conditions and forces the Q outputs Low

Features :-

• Shift right and shift left capability
• Synchronous parallel and serial data transfer
• Easily expanded for both serial and parallel operation
• Asynchronous Master Reset
• Hold (do nothing) mode