74LS257 Quad 2-Input Multiplexer Tri-State IC (74257) DIP-14 Package

74LS257 Quad 2-Input Multiplexer Tri-State IC (74257) DIP-14 Package

In Stock
ENQUIRY!
Category:

These Schottky-clamped high-performance multiplexers feature 3-STATE outputs that can interface directly with data lines of bus-organized systems. With all but one of the common outputs disabled (at a high impedance state), the low impedance of the single enabled output will drive the bus line to a HIGH or LOW logic level. To minimize the possibility that two outputs will attempt to take a common bus to opposite logic levels, the output enable circuitry is designed such that the output disable times are shorter than the output enable times. This 3-STATE output feature means that n-bit (paralleled) data selectors with up to 258 sources can be implemented for data buses. It also permits the use of standard TTL registers for data retention throughout the system.

Description

Features :-

  • 3-STATE versions LS157 and LS158 with same pinouts
  • Schottky-clamped for significant improvement in A-C performance
  • Provides bus interface from multiple sources in high-performance systems
  • Average propagation delay from data input 12 ns
  • Typical power dissipation: 50mW

Specifications :-

  • Supply Voltage : 4.75 – 5.25V
  • Input HIGH Voltage : 2.0V
  • Input LOW Voltage : 0.8V
  • HIGH Level Output Current : -2.6mA
  • LOW Level Output Current : 24
  • Free Air Operating Temperature : 70°C

Package Includes :-

1 X 74LS257 Quad 2-Input Multiplexer Tri-State IC (74257) DIP-14 Package

Reviews

There are no reviews yet.

Be the first to review “74LS257 Quad 2-Input Multiplexer Tri-State IC (74257) DIP-14 Package”

Your email address will not be published. Required fields are marked *

Related products

74HC137 3-to-8 line Decoder/Demultiplexer IC (74138 IC) DIP-16 Package
Add to wishlist Compare

74HC137 3-to-8 line Decoder/Demultiplexer IC (74138 IC) DIP-16 Package

Read more
The 74HC137 decoder utilizes advanced silicon-gate CMOS technology and is well suited to memory address decoding or data routing applications. The circuit features high noise immunity and low power consumption usually associated with CMOS circuitry, yet has speeds comparable to low power Schottky TTL logic. The 74HC137 has 3 binary select inputs (A, B, and C). If the device is enabled, these inputs determine which one of the eight normally HIGH outputs will go LOW. Two active LOW and one active HIGH enables (G1, G2A and G2B) are provided to ease the cascading of decoders. The decoder’s outputs can drive 10 low power Schottky TTL equivalent loads, and are functionally and pin equivalent to the 74LS137. All inputs are protected from damage due to static discharge by diodes to VCC and ground.

Features:-

  • Combines 3-to-8 decoder with 3-bit latch
  • Multiple input enable for easy expansion or independent controls
  • Active LOW mutually exclusive outputs
  • Low-power dissipation
  • Complies with JEDEC standard no. 7A
  • Multiple package options
ENQUIRY!
74F240 Octal Buffers/Line Drivers with 3-State Outputs IC (74240) DIP-20 Package
Add to wishlist Compare

74F240 Octal Buffers/Line Drivers with 3-State Outputs IC (74240) DIP-20 Package

Read more
The 74F240 are octal buffers and line drivers designed to be employed as memory and address drivers, clock drivers and bus-oriented transmitters/receivers which provide improved PC and board density.

Features:-

  • 3-STATE outputs drive bus lines or buffer memory address registers
  • Outputs sink 64mA (48mA mil)
  • 12mA source current
  • Input clamp diodes limit high-speed termination effects
ENQUIRY!
74F533 Octal Transparent Latch with 3-State Outputs IC (74533) DIP-20 Package
Add to wishlist Compare

74F533 Octal Transparent Latch with 3-State Outputs IC (74533) DIP-20 Package

Read more
The 74F533 consists of eight latches with 3-STATE outputs for   bus   organized   system   applications.   The   flip-flops appear transparent to the data when Latch Enable (LE) is HIGH.  When  LE  is  LOW,  the  data  that  meets  the  setup times is latched. Data appears on the bus when the Output Enable (OE) is LOW. When OE is HIGH the bus output is in the high impedance state.

Features :-

  • Eight latches in a single package
  • 3-STATE outputs for bus interfacing
ENQUIRY!
74F541 Octal Buffer/Line Driver with 3-State Outputs IC (74541) DIP-20 Package
Add to wishlist Compare

74F541 Octal Buffer/Line Driver with 3-State Outputs IC (74541) DIP-20 Package

Read more
The 74F541 except that the inputs and outputs are on opposite sides of the package (see Connection Diagrams). This pinout arrangement makes these devices especially useful as output ports for microprocessors, allowing ease of layout and greater PC board density

Features :-

  • 3-STATE outputs drive bus lines
  • Inputs and outputs opposite side of package, allowing easier interface to microprocessors
ENQUIRY!
74F182 Carry Lookahead Generator IC (74182) DIP-16 Package
Add to wishlist Compare

74F182 Carry Lookahead Generator IC (74182) DIP-16 Package

Read more
The 74F182 is a high-speed carry lookahead generator. It is  generally  used  with  the  74F181  or  74F381  4-bit  arithmetic  logic  units  to  provide  high-speed  lookahead  over word lengths of more than four bits

Features :-

  • Provides lookahead carries across a group of four ALUs
  • Multi-level  lookahead  high-speed  arithmetic  operation over long word lengths
ENQUIRY!
74F574 Octal Edge-Triggered D-Type Flip-Flop with 3-State Outputs IC (74574) DIP-20 Package
Add to wishlist Compare

74F574 Octal Edge-Triggered D-Type Flip-Flop with 3-State Outputs IC (74574) DIP-20 Package

Read more
This 8-bit flip-flop features 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. It is particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. The eight flip-flops of the SN74F574 are edge-triggered D-type flip-flops. On the positive transition of the clock (CLK) input, the Q outputs will be set to the logic levels that were set up at the data (D) inputs. A buffered output enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components. The output enable (OE) does not affect the internal operations of the flip-flops. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. The SN74F574 is characterized for operation from 0°C to 70°C.

Features :-

  • Eight D-Type Flip-Flops in a Single Package
  • 3-State Bus-Driving True Outputs
  • Full Parallel Access for Loading
  • Buffered Control Inputs
  • Package Options Include Plastic Small-Outline Packages and Standard Plastic 300-mil DIPs
ENQUIRY!

Product Enquiry