74HC237 3-to-8 line Decoder/Demultiplexer IC (74237 IC) DIP-16 Package

74HC158 is a 16 Pin Quad 2-Input Multiplexer IC having 2V to 6V Operating Voltage range with 1uA Low Input current and high noise immunity. It select 4 bits of data from two sources under the control of a common data select input (S). The enable input (E) is active LOW. When E is HIGH, all of the outputs (1Y to 4Y) are forced LOW regardless of all other input conditions.

Features:-

• Common Select Input
• Separate Enable Inputs
• Buffered inputs and Outputs
• Fanout (Over Temperature Range)
• Standard Outputs  : 10 LSTTL Loads
• Bus Driver Outputs : 15 LSTTL Loads
• Wide Operating Temperature Range : -55oC to 125oC
• Balanced Propagation Delay and Transition Times
• Significant Power Reduction Compared to LSTTL Logic ICs
• HC Types
• 2V to 6V Operation
• High Noise Immunity: NIL = 30%, NIH = 30%of VCC at VCC = 5V
• HCT Types-
• 4.5V to 5.5V Operation
• Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min)
• CMOS Input Compatibility, Il≤1μA at VOL, VOH

 

The 74F109 is a dual positive edge-triggered JK-type flip-flop featuring individual J, K, clock, set, and reset inputs; also true and complementary outputs. Set (SD) and reset (RD) are asynchronous active low inputs and operate independently of the clock (CP) input. The J and K are edge-triggered inputs which control the state changes of the flip-flops as described in the function table. Clock triggering occurs at a voltage level and is not directly related to the transition time of the positive-going pulse. The J and K inputs must be stable just one setup time prior to the low-to-high transition of the clock for predictable operation. The JK design allows operation as a D flip-flop by tying J and K inputs together. Although the clock input is level sensitive, the positive transition of the clock pulse between the 0.8V and 2.0V levels should be equal to or less than the clock to output delay time for reliable operation

Features :-

Industrial temperature range available (–40°C to +85°C)

The 74HC163; 74HCT163 is a synchronous presettable binary counter with an internal look-head carry. Synchronous operation is provided by having all flip-flops clocked simultaneously on the positive-going edge of the clock (CP). The outputs (Q0 to Q3) of the counters may be preset to a HIGH or LOW. A LOW at the parallel enable input (PE) disables the counting action. It causes the data at the data inputs (D0 to D3) to be loaded into the counter on the positive-going edge of the clock. Preset takes place regardless of the levels at count enable inputs (CEP and CET). A LOW at the master reset input (MR) sets Q0 to Q3 LOW after the next positive-going transition on the clock input (CP). This action occurs regardless of the levels at input pins PE, CET and CEP. This synchronous reset feature enables the designer to modify the maximum count with only one external NAND gate. The look-ahead carry simplifies serial cascading of the counters. Both CEP and CET must be HIGH to count. The CET input is fed forward to enable the terminal count output (TC). The TC output thus enabled will produce a HIGH output pulse of a duration approximately equal to a HIGH output of Q0. This pulse can be used to enable the next cascaded stage. Inputs include clamp diodes. This enables the use of current limiting resistors to interface inputs to voltages in excess of VCC

Features :-

• Complies with JEDEC standard no. 7A
• Input levels:

For 74HC163: CMOS level For 74HCT163: TTL level

• Synchronous counting and loading
• 2 count enable inputs for n-bit cascading
• Synchronous reset
• Positive-edge triggered clock
• ESD protection:

HBM JESD22-A114F exceeds 2 000 V MM JESD22-A115-A exceeds 200 V

• Multiple package options
• Specified from -40 °C to +85 °C and -40 °C to +125 °C

The 74F164 is an 8-bit edge-triggered shift register with serial data entry and an output from each of the eight stages. Data is entered through one of two inputs (Dsa, Dsb); either input can be used as an active High enable for data entry through the other input. Both inputs must be connected together or an unused input must be tied High. Data shifts one place to the right on each Low-to-High transition of the clock (CP) input, and enters into Q0 the logical AND of the two data inputs (Dsa, Dsb) that existed one setup time before the rising edge. A Low level on the Master Reset (MR) input overrides all other inputs and clears the register asynchronously, forcing all outputs Low.

Features :-

• Gated serial data inputs
• Typical shift frequency of 100MHz
• Asynchronous Master Reset
• Buffered clock and data inputs
• Fully synchronous data transfer
• Industrial temperature range available (–40 to +85 °C)