AT89C55 Microcontroller - 24MHz - 8 Bit - 40 Pin

AT89C55 Microcontroller – 24MHz – 8 Bit – 40 Pin

In Stock
ENQUIRY!
Category:

The AT89C55 is a 8-bit low-power High-performance CMOS Microcontroller with 20kB of flash programmable read only memory and 256 bytes of RAM. The device is manufactured using Atmel’s high-density non-volatile memory technology and is compatible with the industry standard 80C51 and 80C52 instruction set and pinout. The on-chip Flash allows the program memory to be user programmed by a conventional non-volatile memory programmer. By combining a versatile 8-bit CPU with flash on a monolithic chip, the Atmel AT89C55 is a powerful microcomputer which provides a highly flexible and cost effective solution to many embedded control applications. The AT89C55 provides the following standard features 20kB of Flash, 256 bytes of RAM, 32 I/O lines, three 16-bit timer/counters, a six-vector, two-level interrupt architecture, a full-duplex serial port, on-chip oscillator and clock circuitry.

Description

Features:-

  • Compatible with MCS-51 products
  • 20kB Reprogrammable flash memory
  • 10,000 Write/erase cycles endurance
  • Three-level program memory lock
  • 256 x 8-bit Internal RAM
  • 32 Programmable I/O lines
  • Three 16-bit timers/counters
  • Eight interrupt sources
  • Programmable serial channel
  • Low-power idle and power-down modes
  • Interrupt recovery from power-down mode
  • Hardware watchdog timer
  • Dual data pointer
  • Power-off flag

Reviews

There are no reviews yet.

Be the first to review “AT89C55 Microcontroller – 24MHz – 8 Bit – 40 Pin”

Your email address will not be published. Required fields are marked *

Related products

P89V51RD2 Microcontroller
Add to wishlist Compare

P89V51RD2 Microcontroller

Read more
The P89V51RD2 is an 80C51 microcontroller by NXP (Phillips) with 64 kB Flash and 1024 bytes of data RAM. A key feature of the P89V51RD2 is its X2 mode option. The design engineer can choose to run the application with the conventional 80C51 clock rate (12 clocks per machine cycle) or select the X2 mode (6 clocks per machine cycle) to achieve twice the throughput at the same clock frequency. Another way to benefit from this feature is to keep the same performance by reducing the clock frequency by half, thus dramatically reducing the EMI. The Flash program memory supports both parallel programming and in serial In-System Programming (ISP). Parallel programming mode offers gang-programming at high speed, reducing programming costs and time to market. ISP allows a device to be reprogrammed in the end product under software control. The capability to field/update the application firmware makes a wide range of applications possible. The P89V51RD2 is also In-Application Programmable (IAP), allowing the Flash program memory to be reconfigured even while the application is running.
ENQUIRY!
AT89S51 Microcontroller
Add to wishlist Compare

AT89S51 Microcontroller

Read more
AT89S51 Microcontroller
ENQUIRY!
P80C51 Microcontroller – 8 Bit – 40 Pin
Add to wishlist Compare

P80C51 Microcontroller – 8 Bit – 40 Pin

Read more
The 80C51 has separate address spaces for program and data memory. The Program memory can be up to 64k bytes long. The lower 4k can reside on-chip. Figure 1 shows a map of the 80C51 program memory. The 80C51 can address up to 64k bytes of data memory to the chip. The MOVX instruction is used to access the external data memory. The 80C51 has 128 bytes of on-chip RAM, plus a number of special function Registers (SFRs). The lower 128 bytes of RAM can be accessed either by direct addressing (MOV data addr) or by indirect addressing (MOV @Ri).
ENQUIRY!
AT89S8252 Microcontroller – 24MHz – 8 Bit – 40 Pin
Add to wishlist Compare

AT89S8252 Microcontroller – 24MHz – 8 Bit – 40 Pin

Read more
The AT89S8252 is a low-power, high-performance CMOS 8-bit microcomputer with 8K bytes of downloadable Flash programmable and erasable read only memory and 2K bytes of EEPROM. The device is manufactured using Atmel’s high-density nonvolatile memory technology and is compatible with the industry-standard 80C51 instruction set and pinout. The on-chip downloadable Flash allows the program memory to be reprogrammed in-system through an SPI serial interface or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with downloadable Flash on a monolithic chip, the Atmel AT89S8252 is a powerful microcomputer which provides a highly-flexible and cost-effective solution to many embedded control applications.
ENQUIRY!
AT89C51 Microcontroller
Add to wishlist Compare

AT89C51 Microcontroller

Read more
The AT89C51 is a low-power, high-performance CMOS 8-bit microcomputer with 4K bytes of Flash Programmable and Erasable Read Only Memory (ROM). The device is manufactured using Atmel’s high density nonvolatile memory technology and is compatible with the industry standard MCS-51™ instruction set and pin out. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89C51 is a powerful microcomputer which provides a highly flexible and cost effective solution to many embedded control applications.
ENQUIRY!
ATmega328P Microcontroller with Arduino BootLoader
Add to wishlist Compare

ATmega328P Microcontroller with Arduino BootLoader

Read more
Arduino UNO uses ATMEGA328P-PU microcontroller and this controller comes pre-loaded with a Arduino UNO bootloader. Basically bootloader is a little piece of code that allows you to program the flash memory of the Arduino’s atmega328p via serial or USB instead of using an ICSP programmer.
If you are making a project based on Arduino UNO & you have made a customized PCB then you will be requiring bootloaded Atmega328 microcontroller. This is a ATmega328 in DIP package, pre-loaded with the Arduino (16MHz) Bootloader. This will allow you to use Arduino code in your custom embedded project without having to use an actual Arduino board. To get this chip working with Arduino IDE, you will need an external 16MHz crystal or resonator, a 5V supply, and a serial connection. You should select the Arduino UNO board within the Arduino IDE.
ENQUIRY!

Product Enquiry