CD74HC670 High Speed CMOS Logic 4-by-4 Register IC (74670 IC) DIP-16 Package

The 74F251 is a high-speed 8-input digital multiplexer. It provides, in one package, the ability to select one bit of data from up to eight sources. It can be used as a universal function generator to generate any logic function of four variables. Both assertion and negation outputs are provided

Features :-

• Multifunctional Capacity
• On-Chip Select Logic Decoding
• Inverting and Noninverting 3-State Output

The functional characteristics of the 74F194 4-Bit Bidirectional Shift Register are indicated in the Logic Diagram and Function Table. The register is fully synchronous, with all operations taking place in less than 9ns (typical) for 74F, making the device especially useful for implementing very high speed CPUs, or for memory buffer registers. The 74F194 design has special logic features which increase the range of application. The synchronous operation of the device is determined by two Mode Select inputs, S0 and S1. As shown in the Mode Select-Function Table, data can be entered and shifted from left to right (shift right, Q0→Q1, etc.), or right to left (shift left,Q3→Q2, etc.), or parallel data  can be entered, loading all 4 bits of the register simultaneously. When both S0 and S1 are Low, existing data is retained in a hold (do nothing) mode. The first and last stages provide D-type Serial Data inputs (DSR, DSL) to allow multistage shift right or shift left data transfers without interfering with parallel load operation. Mode Select and data inputs on the74F194 are edge-triggered, responding only to the Low-to-High transition of the Clock (CP). Therefore, the only timing restriction is that the Mode Select and selected data inputs must be stable one setup time prior to the Low-to-High transition of the clock pulse. Signals on the Mode Select, Parallel Data (D0–D3) and Serial Data(DSR, DSL) can change when the clock is in either state, provide donly the recommended setup and hold times, with respect to the clock rising edge, are observed. The four Parallel Data inputs(D0–D3) are D-type inputs. Data appearing on (D0–D3) inputs whenS0 and S1 are High is transferred to the Q0–Q3 outputs respectively, following the next Low-to-High transition of the clock. When Low, the asynchronous Master Reset (MR) overrides all other input conditions and forces the Q outputs Low

Features :-

• Shift right and shift left capability
• Synchronous parallel and serial data transfer
• Easily expanded for both serial and parallel operation
• Asynchronous Master Reset
• Hold (do nothing) mode

74HC158 is a 16 Pin Quad 2-Input Multiplexer IC having 2V to 6V Operating Voltage range with 1uA Low Input current and high noise immunity. It select 4 bits of data from two sources under the control of a common data select input (S). The enable input (E) is active LOW. When E is HIGH, all of the outputs (1Y to 4Y) are forced LOW regardless of all other input conditions.

Features:-

• Common Select Input
• Separate Enable Inputs
• Buffered inputs and Outputs
• Fanout (Over Temperature Range)
• Standard Outputs  : 10 LSTTL Loads
• Bus Driver Outputs : 15 LSTTL Loads
• Wide Operating Temperature Range : -55oC to 125oC
• Balanced Propagation Delay and Transition Times
• Significant Power Reduction Compared to LSTTL Logic ICs
• HC Types
• 2V to 6V Operation
• High Noise Immunity: NIL = 30%, NIH = 30%of VCC at VCC = 5V
• HCT Types-
• 4.5V to 5.5V Operation
• Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min)
• CMOS Input Compatibility, Il≤1μA at VOL, VOH

 

The 74F393 is a Dual Ripple Counter with separate Clock (CPn) and Master Reset (MR) inputs to each counter. The two counters are identified by the “a” and “b” suffixes in the pin configuration. The operation of each half of the 74F393 is the same. The counters are triggered by a High-to-Low transition of the Clock (CPa and CPb)inputs. The counter outputs are internally connected to provide Clock inputs to succeeding stages. The outputs of the ripple counter do not change synchronously and should not be used for high speed address decoding. The Master Resets (MRa and MRb) are active High asynchronous inputs; one for each 4-bit counter. A High level in the MR input overrides the Clock and sets the outputs Low

Features :-

• Two 4-bit binary counters
• Two Master Resets to clear each 4-bit counter individually