74HC541 Octal 3-State Buffer/Line Driver IC (74541 IC) DIP-20 Package

The 74HC20 is a 14 Pin Quad 4-Input NAND Gate IC. This device contains four independent gates each of which performs the logic NAND function. NAND gates utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard CMOS integrated circuits. All gates have buffered outputs. All devices have high noise immunity and the ability to drive 10 LS-TTL loads. The 74HC logic family is functionally as well as pin-out compatible with the standard 74LS logic family. All inputs are protected from damage due to static discharge by internal diode clamps to VCC and ground.

74HC109 Dual J-K Positive-Edge-Triggered Flip-Flop IC – DIP-16 Package The 74HC109 is a dual positive edge triggered JK flip-flop featuring individual nJ and nK inputs. It has clock (nCP) inputs, set (nSD) and reset (nRD) inputs and complementary nQ and nQ outputs. The set and reset are asynchronous active LOW inputs and operate independently of the clock input. The nJ and nK inputs control the state changes of the flip-flops as described in the mode select function table. The nJ and nK inputs must be stable one set-up time prior to the LOW-to-HIGH clock transition for predictable operation. The JK design allows operation as a D-type flip-flop by connecting the nJ and nK inputs together. Inputs include clamp diodes. It enables the use of current limiting resistors to interface inputs to voltages in excess of VCC. This product is known as 74109 IC, 74109 SMD IC, 74HC109 IC, 74HC109 SMD IC, Components, Dual J-K Positive-Edge-Triggered Flip-Flops IC, Dual J-K Positive-Edge-Triggered Flip-Flops SMD IC, SN74HC109D, CD74HC109M, 74HC109D, CD74HC109E, SN74HC109N, CD74HC109ME4.

Features :-

• Input Levels :

– For 74HC109: CMOS level – For 74HCT109: TTL level

• J and K inputs for easy D-type flip-flop
• Toggle flip-flop or “do nothing” mode
• Specified in compliance with JEDEC standard no. 7A
• ESD protection:

– HBM JESD22-A114F exceeds 2000 V – MM JESD22-A115-A exceeds 200 V

• Multiple package options

The 74F164 is an 8-bit edge-triggered shift register with serial data entry and an output from each of the eight stages. Data is entered through one of two inputs (Dsa, Dsb); either input can be used as an active High enable for data entry through the other input. Both inputs must be connected together or an unused input must be tied High. Data shifts one place to the right on each Low-to-High transition of the clock (CP) input, and enters into Q0 the logical AND of the two data inputs (Dsa, Dsb) that existed one setup time before the rising edge. A Low level on the Master Reset (MR) input overrides all other inputs and clears the register asynchronously, forcing all outputs Low.

Features :-

• Gated serial data inputs
• Typical shift frequency of 100MHz
• Asynchronous Master Reset
• Buffered clock and data inputs
• Fully synchronous data transfer
• Industrial temperature range available (–40 to +85 °C)

74HC158 is a 16 Pin Quad 2-Input Multiplexer IC having 2V to 6V Operating Voltage range with 1uA Low Input current and high noise immunity. It select 4 bits of data from two sources under the control of a common data select input (S). The enable input (E) is active LOW. When E is HIGH, all of the outputs (1Y to 4Y) are forced LOW regardless of all other input conditions.

Features:-

• Common Select Input
• Separate Enable Inputs
• Buffered inputs and Outputs
• Fanout (Over Temperature Range)
• Standard Outputs  : 10 LSTTL Loads
• Bus Driver Outputs : 15 LSTTL Loads
• Wide Operating Temperature Range : -55oC to 125oC
• Balanced Propagation Delay and Transition Times
• Significant Power Reduction Compared to LSTTL Logic ICs
• HC Types
• 2V to 6V Operation
• High Noise Immunity: NIL = 30%, NIH = 30%of VCC at VCC = 5V
• HCT Types-
• 4.5V to 5.5V Operation
• Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min)
• CMOS Input Compatibility, Il≤1μA at VOL, VOH